Penosil FastFoam 123 870ml Ultra-fast-curing gun foam for window and door installation

Application

• Sealing of window and door joints
• Sealing and joining of doors
• Insulation of gaps
• Reducing the effect of thermal bridges
• Thermal insulation and sound insulation

ADHESION

• Wood
• Concrete
• Masonry
• All metals
• PVC
• Bricks
• Gypsumboard
• EPS
• Varnished and painted surfaces

Air temperature during application: +5°C to +35°C. Make sure that the ambient temperature remains within this range until the foam has fully cured.
Can temperature during application: +10°C to +30°C, best results at +20°C.

Surface preparation
Remove dust, dirt and oil stains from surfaces. Moisten dry substrates by spraying with water (only at temperatures above zero) for best results. Protect adjacent surfaces with paper, plastic film or other suitable material. If necessary, use additional weather protection (rain, wind, etc.) when working outdoors.

Usage
Shake the foam can thoroughly at least 20 times. Remove the cap. Hold the foam can in an upright position with the valve facing up. Screw the foam can tightly onto the gun, holding the gun handle with one hand and screwing the can onto the can with the other. Make sure the gun is not pointed at people. Avoid screwing the can onto the gun with the valve facing down. Do not screw the gun onto the can. Do not bend or turn the can while screwing. The working position of the can after attachment is with the bottom facing up. The foam flow can be adjusted with the gun trigger and the adjustment screw.
Fill the joint by approximately 65%, as the foam expands. When filling larger joints, apply the foam in several layers and moisten the foam between layers for better results.
This foam hardens faster than regular foam. Clean the tip of the gun during breaks.
After hardening, cut off excess foam.

Cleaning
Use Penosil Foam Cleaner to clean tools and surfaces from unhardened foam. Hands, clothes and the foam gun can also be cleaned from unhardened foam with Penosil Cleaning Wipes. Hardened foam can be removed mechanically after softening with Penosil Foam Remover.

Label Elements:
CLP Regulation (EC) No. 1272/2008

Danger

Hazard Statements:

H222 – Extremely flammable aerosol.

H229 – Pressurized container: may burst if heated.

H315 – Causes skin irritation.

H317 – May cause an allergic skin reaction.

H319 – Causes serious eye irritation.

H332 – Harmful if inhaled.

H334 – May cause allergy or asthma symptoms or breathing difficulties if inhaled.

H335 – May cause respiratory irritation.

H351 – Suspected of causing cancer.

H373 – May cause damage to organs through prolonged or repeated exposure.

Precautionary Statements:

P101 – If medical advice is needed, have product container or label at hand.

P102 – Keep out of reach of children.

P210 – Keep away from heat, hot surfaces, sparks, open flames and other ignition sources. No smoking.

P211 – Do not spray on an open flame or other ignition source.

P251 – Do not pierce or burn, even after use.

P271 – Use only outdoors or in a well-ventilated area.

P280 – Wear protective gloves/protective clothing/respiratory protection/eye protection/protective footwear.

P304+P340 – IF INHALED: Remove person to fresh air and keep comfortable for breathing.

P305+P351+P338 – IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing.

P410+P412 – Protect from sunlight. Do not expose to temperatures exceeding 50 °C/122 °F.

P501 – Dispose of contents/container in accordance with local/regional/national/international regulations.

Supplemental Information:

EUH204 – Contains isocyanates. May produce an allergic reaction.

Substances Contributing to Classification:

4,4'-Methylenediphenyl diisocyanate (MDI), isomers and homologues.

Reaction products of phosphorus oxychloride and 2-methyloxirane.

Additional Labelling:

Persons already sensitized to diisocyanates may develop allergic reactions when using this product.

Persons suffering from asthma, eczema or skin conditions should avoid contact with this product, including skin contact.

When working with this product in poorly ventilated areas, wear a protective mask equipped with an appropriate gas filter (e.g. an A1 type filter complying with EN 14387).

From 24 August 2023, adequate training is required before industrial or professional use.

Wolf Group OÜ
Suur-Paala 10
13619 Tallinn, Estonia

Phone: +372 605 9300
Fax: +372 605 9315

E-mail: sds@wolf-group.com
Website: www.wolf-group.com