Logo
Categories chevron down Created with Sketch.
Sale

Your cart is empty

To add products to cart, please visit our product catalog.

Tikkurila MULTISTOP 1L Sealing primer for wooden surfaces

Article: 1303781

Category: Primers

Unit: pc.

Barcode: 6408070072530

20,90 €/pc.
Available in stores:
t/c Sāga
Description
Sealing primer for the prevention of discoloration on interior wooden surfaces.
Product features

Suitable as primer and intermediate coat for both untreated and previously painted or varnished (with the exception of certain parquet lacquers), new or old wood surfaces in dry interior premises. Prevents discoloring wood extracts and other yellowing substances such as tar, etc. from entering into the top coat. Prevents discoloration caused by wood knots.

Recommended uses
Ceiling and wall panels, wooden floors, skirting, doors, windows and furniture.
TECHNICAL DATA
The paint is suitable for interior walls The paint is full-matt The paint is water-borne Tool: roller Tool: spray Tool: brush 
The coverage of the paint on rough surfaces

m2/l
The coverage of the paint on smooth surfaces

m2/l
Colour Range
White F497
Gloss grade
Full-matt
Coverage
7 m²/l  (minimum amount to be applied 260 g/m², wet film thickness 200 µm, dry film thickness 75 µm)
Can sizes
1, 3 and 10 L
Thinner
Water
Mixing ratio
To be used unthinned.
Application method
Brush, roller or spray gun.
Airless spray:
- nozzle 0.015" 0.019"
- thinning 0-10 vol %

Drying time at 23°C and 50% relative air humidity
Touch-dry after approx. one hour. 
Recoatable the following day.
Solids volume
38 %
Density
1.3 kg/l, ISO 2811
Storage
Protect from frost.

APPLICATION DETAILS
Application conditions
The surface to be painted must be dry, the temperature at least +10°C, and the relative humidity of the air less than 80 %. A low temperature (approx. +15°C) and higher humidity (50–70 % RH) will extend the working time and make application easier.
Preparation
In order to ensure the best possible adhesion, clean new wooden surfaces from any dirt and dust. 
Wash previously painted or lacquered surfaces with neutral detergent according to need. Allow to dry. Remove loose paint or lacquer and sand the whole surface – especially floors and furniture. Remove sanding dust. If necessary, use Presto Rapid Filler to fill any cracks and dents, and sand the filled areas. Remove sanding dust. Patch paint with primer on bare wood surfaces. 

Note! The adhesion of Multistop to certain parquet lacquers is poor, therefore the parquet lacquer should be completely removed, if Multistop is used over the entire surface.
Painting
Stir Multistop well before use. The product is used without thinning. Apply plenty of the paint and treat 1-2 times, preferably with a thick nap roller and finish the surface immediately with a synthetic brush. The best insulation result is achieved when the treatment is performed twice. Allow the surface to dry until the following day before the second coat. Thus it forms the best protection against discoloration from the wood.
Cleaning of tools
Remove any excess paint from tools. Wash the tools with water. Tikkurila Pensselipesu (Tool Cleaner) is recommended for removing slightly hardened paint.
Maintenance instructions
After the surface treatment, surfaces must be handled with care for a few weeks, as the product will reach its final hardness and durability under normal conditions after about a month. 
About a month after painting at the earliest, if necessary, clean the surface using neutral (pH 6–8) dishwashing liquid solution and a soft brush, sponge or cloth. Clean soiled surfaces using mild alkaline (pH 8–10) detergent solution and a cloth, mop or sponge, for example. Rinse the surface carefully. 
Weight 1.10 kg
Brand TIKKURILA